Test Systems
group of interoperable devices whose integration perform a common test purpose.
See Also: Systems, Equipment, System Integrators, System Test, System Integration
-
product
Bluetooth Enabled Signal Conditioners I/O Modules
microBlox
Acromag's microBlox uB Series I/O modules offer a compact, high-performance solution for interfacing sensors and field devices with data acquisition systems. uB signal conditioning modules are ideal to isolate, filter, convert and amplify a wide variety of signal types for test, measurement and control systems. Just plug uB modules into 4, 8, or 16-channel backpanels in any mix for a high-density analog I/O interface. Channel-to-channel isolation provides optimal noise and surge protection from ground loops, spikes, and high common mode voltages.
-
product
LC Software
Total Solution for PIC/S and FDA Compliance
All Shimadzu network system products incorporate functions for the PIC/S GMP and the Part 11 compliance regulation, and computerized system validation functions required by GxP. Shimadzu provides documentation including IQ/OQ, Certificates of Compliance, and Inspection Test Result Reports based on Shimadzu IS09001 certified system. Shimadzu's accredited service personnel offer full support for validation of customer's Shimadzu products. In the latest information on PIC/S and FDA regulations through seminars and workshops, participating in vendor audits demanded by agencies, and actively assisting customers to comply with new regulations.
-
product
Dynamometer
I-Series
AW I-Series dynamometers are excellent for diesel engine testing as well as other applications. The electronic load control system on this hydraulic activated dynamometer allows for precise and steady control of Power and RPM levels.
-
product
Full Band Noise Figure and Gain Test Extenders
STG-06-S1
Full band noise figure and gain test extenders are offered to extend noise and gain measuring capabilities up to higher millimeterwave frequency ranges. These extenders are designed to interface with noise and gain test systems that have an input IF of 10 MHz to 1.6 GHz, such as the industry standard Keysight 8970A/B, N8975A and Maury MT 2075B. The noise figure and gain test extenders include a high-performance, solid-state noise source (STZ series) and a full waveguide down converter (STC serie...show more -
product
FaithTech FTLP Series 100W/180W Portable Programmable DC Power Supply
FaithTech FTLP Series
Shenzhen FaithTech Technology Co., Ltd.
FTLP series is a kind of programmable Portable bench DC power supply, with the widest output range, which allows engineers to test more program requirements with just one device. To be exact, the FTLP series provides full power all the way down to 25% of the rated output voltage. The FTLP series is equipped with RS232 and RS485 as standard interfaces that are essential for system integration, you can also choose USB or LAN interface as your add-on interfa...show more -
product
PXI High Density Precision Resistor Module, 9-Channel, 2.5Ω to 472Ω
40-298-020
The 40-298-020 is a high density programmable resistor module with 9 channels which can be set between 2.5Ω and 472Ω with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
EMCTD Broadband RF Safety Systems
The EMCTD analog Smart Fieldmeter® is easy to read and to operate. The EMCTD broadband electromagnetic probe covers the 0.2 to 3000 MHz spectrum where most common industrial, communications, medical and government RF emitters are found. The ANGPE-3000 system enables checking of home, office, and workplace RF levels. The system is designed to conveniently measure RF levels around WiFi access points, RFID systems and rooftop antennas; to find transmitter cabinet radiation, locate transmissio...show more -
product
Thermal Vacuum Chamber & Control
Based on several successful deliveries of complex DAQ systems, WinSoft was selected by 2 major satellite manufacturers to design and build a DAQ and Control systems which are connected to various thermal vacuum chambers - all connected to a central database.The chambers are used for environmental testing. The data collected by the DAQ system is recorded continuously every few seconds over a period of a few months.
-
product
Imaging Gauge Software Test System
The IMAGING GAUGETM quality analysis system was developed by APPLIED IMAGE to address the growing need to standardize the evaluation of camera image quality. The system includes a Test Chart manufactured using our ACCUedge® technology, along with unique Image Analysis Software, used together to analyze the quality of the imaging system, and then provide a summary report on the various image quality metrics. Our goal is to provide a simple to use, unique image analysis system, that can be utilized by R&D, scientists, system integrators, technicians and field operators to evaluate the camera quality or imaging system.
-
product
Radio Testing
Testing of radio systems. PHOENIX TESTLAB as an accredited radio testing laboratory, Notified Body for R&TTE Directive 99/5/EC and Conformity Assessment Body offers you a complete service up to your products' worldwide introduction to the market.
-
product
High-Speed Digital Image Correlation System
Q-450
The 3D High-Speed Image Correlation System Q-450 allows the full-field, non-contact and three-dimensional dynamic measurement of shape, displacements and strains on components and structures made from almost any material. Based on the digital image correlation technique, the Q-450 system is designed for full-field vibration analysis and high speed transient events. This makes it ideal for ballistics testing, fracture mechanics, shock excitations, the Hopkinson Bar test, or Impact Testing.
-
product
ESD Test System
58154 Series
ESD (Electrostatic Discharge) Test Systems are PXI/PCI controlled module to simulate electrostatic discharge pulse during electronic device testing. The 58154 series offer both ESD STM5.1-2001-Human Body Model and ESD STM5.2-1999-Machine Model. The user friendly software offers programmable and flexible features, such as sampling test on a wafer, ESD model, ESD pulse polarity, ESD pulse interval in a sequence, and automatic testing function.
-
product
Test System
BMS HIL
The BMS Hardware-in-the-Loop (HIL) Test System is a high performance platform providing all necessary input signals used for battery pack simulation. A real-time operating system executes complex cell and pack models commonly used for BMS algorithm development and firmware regression testing.
-
product
(100kN) Fatigue Testing Systems
8801
The 8801 servohydraulic testing system meets the challenging demands of a varied range of both dynamic and static testing requirements. The 8801 provides complete testing solutions to satisfy the needs of advanced materials and component testing, and is ideally suited for high- and low-cycle fatigue testing, thermomechanical fatigue testing, and fracture mechanics. The higher capacity of up to 100 kN, a larger working space, a high stiffness, and the precision of alignment all make the 8801 an exceptionally versatile and reliable testing system.
-
product
GNSS Testing & Simulation
Safran Federal Systems is a leading provider of advanced GNSS Testing & Simulation systems and tools for NAVWAR environments.
-
product
PXI High Density Precision Resistor Module, 6-Channel, 4Ω to 5.82MΩ
40-298-052
The 40-298-052 is a high density programmable resistor module with 6 channels which can be set between 4Ω and 5.82MΩ with 0.5Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
-
product
Digital Subsystem
DD48
The DD48 is a self-contained, single slot AXIe 3.1, 48 channel mixed-signal digital test subsystem. Each DD48 has an independent sequencer controller with pattern generators, and an independent per-channel timing system. Integrated timing generators connect directly to the instrument’s pin electronics. Each board can operate independently or synchronously with other DD48 cards.
-
product
Steady-state Solar Simulator For PV Modules
SORAS LS
In certification laboratories for photovoltaic modules, steady-state solar simulators are mostly used for stabilization / light soaking tests (MQT 19) and hot-spot endurance tests (MQT 09) according to IEC 61215 and IEC 61730. An initial stabilization is required for all PV modules that undergo a standard test procedure. For the hot-spot endurance test (MQT 09), it is important that the operator has easy access to the front and back site of the module. During the test, it is necessary to shade o...show more -
product
Combination Wave Generator
Shanghai Guantu Technology Co., Ltd.
GCW series combined wave generators can generate high energy surges for combined wave testing. It has the characteristics of fast rise and long pulse duration. According to different modulation components, different surge waveforms can be generated; the control system can automatically record and analyze the above surge waveforms. standard:IEC60060-4-5, IEC61643-11, UL1449-2006, GB18802.1, GB/T18802.21,
-
product
Integrated Transformer Test Van
XD90
Hangzhou Xihu Electronic Institute
The XD90 integrated modular power system testing vehicle provides an integrated yet flexible solution of preforming a wide selection of normal and specialty tests on power equipment. Designed with the effectiveness and efficiency of power testing in mind, this platform achieves the goal of “integration of functions” instead of just a “combination of instruments”. Not only it provides an abundant means of power testing, but with optimized device placement, operational convenience, and safety factor.
-
product
Powerful, Fully Integrated Workstation for Emission Microscopy
PEM-1000
The PEM-1000 emission microscope incorporates the latest technology in real time, high quantum efficiency, mega-pixel CCD detectors in a back-thinned cooled camera. A portable system, the PEM 1000 can interface with all analytical probe stations, ATE (automated test equipment) and bench top configurations for high speed functional testing.
-
product
Hipot Tests
The hipot test (high potential test) or dielectric withstand test, is used to determine the insulation and dielectric strength. It is carried out on modules, devices and systems of protection class I + II. In this test, the insulation of the test object is subjected to greater stress by the high voltage than in normal operation. It is determined whether the insulation of all current-carrying conductors, as well as the safety distance to the enclosure, is sufficient and complies with the legal re...show more -
product
Testing Released Water Vapor
Humiditest™ Complete System
The James Instruments Humitest System allows the concrete practitioner to monitor and ensure that a new structure is dry enough to proceed with the next phase of construction. This is especially critical for concrete structures requiring a coating, carpeting or similar floor or covering treatment. Installing such treatments before the concrete is sufficiently dry will typically cause expensive failures in the covering treatment. The only accurate way to ensure that the concrete is sufficiently dry enough to safely avoid expensive re-work is via a bore hole humidity test system, such as the Humitest System
-
product
PXIe-8521, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module
786771-01
PXIe, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8521 is a 100BASE-T1 unshielded twisted pair (UTP) Automotive Ethernet interface for developing applications with the NI‑XNET driver. The PXIe-8521 is ideal for developing applications that require … Automotive Ethernet to test and validate automotive electronic control units (ECUs). The interface provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware t...show more -
product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1Ω to 470Ω
40-251-114
The 40-251-114 is a programmable resistor module with 4 channels which can be set between 1Ω and 470Ω with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Antenna Test Facility
Raytheon’s Antenna Test Facility (ATF) provides state-of-the-art measurement capabilities to assist in the development of advanced antenna technologies for a variety of airborne and space applications such as advanced radar and communication systems. The ATF is available for use by Raytheon businesses as well as other companies that design and prototype new and experimental antennas.
-
product
Solar Cell Testers
Solar Cell Testers are integrated systems incorporating Solar Simulator and I-V Measurement systems. PET offers Standard and Advance IV Measurement software. PET Cell Testers are capable of measuring a diverse range of solar cell parameters such as Isc,Voc, Imax,Vmax, Pmax, FF, Rsh, Rs and η cell conversion efficiency, complete light and dark I-V curves. All that needs to be done to test a cell is to load the cell, make electrical probes contact and press “Measure” icon on the I-V Measurement Sy...show more -
product
Coaxial Switch, DC to 40 GHz, SPDT
8765D
The Keysight 8765 family of switches is designed for microwave instrumentation and ATE systems and features excellent electrical and mechanical performance. The Keysight 8765D is equipped with SMA connectors and operates from dc to 26.5 GHz with 3.5mm connectors and 40 GHz with 2.4 mm connectors. Option 292 can be ordered with Keysight 8765D. It is available with voltage option covering any drive voltage between 4.5 volts and 32 volts dc. Where performance data are required, Option UK6 includes a printout of test results. This switch is designed from the ground up for maximum dependability and performance. It is designed to operate within its specifications for more than 10,000,000 cycles.
-
product
PXI 40Amp 14Volt 2xSPST Automotive Relay
40-180-001
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDCThe 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
